冶炼资讯：
一般强度船体结构用钢分为D4个等级的钢材的屈服强度（不小于235N/mm2）和抗拉强度（4-52N/mm2）一样，只是不同温度下的冲击功不一样而已.高强度船体结构用钢按其屈服强度划分强度等级，每一强度等级又按其冲击韧性的不同分为F1级。A3D3E3F32的屈服强度不小于315N/mm2,抗拉强度44-57N/mm2,F分别表示其各自可分别在：度、-2度、-4度、-6度的情况下所能达到的冲击韧性。
欧标角钢钢执行标准：EN标准
欧标角钢规格型号表
品 名 规格型号 材质 米重/公斤
欧标角钢 30*30*3 S235/275/355/JR/J0/J2 1.36
欧标角钢 40*40*4 S235/275/355/JR/J0/J2 2.42
欧标角钢 40*40*5 S235/275/355/JR/J0/J2 2.97
欧标角钢 50*50*4 S235/275/355/JR/J0/J2 3.06
欧标角钢 50*50*5 S235/275/355/JR/J0/J2 3.77
欧标角钢 50*50*6 S235/275/355/JR/J0/J2 4.47
欧标角钢 60*60*4 S235/275/355/JR/J0/J2 3.70
欧标角钢 60*60*5 S235/275/355/JR/J0/J2 4.57
欧标角钢 60*60*6 S235/275/355/JR/J0/J2 5.42
欧标角钢 63*63*6 S235/275/355/JR/J0/J2 5.72
欧标角钢 65*65*4 S235/275/355/JR/J0/J2 4.02
欧标角钢 65*65*5 S235/275/355/JR/J0/J2 4.97
欧标角钢 65*65*8 S235/275/355/JR/J0/J2 7.73
欧标角钢 70*70*6 S235/275/355/JR/J0/J2 6.38
欧标角钢 70*70*7 S235/275/355/JR/J0/J2 7.38
欧标角钢 70*70*8 S235/275/355/JR/J0/J2 8.37
欧标角钢 75*75*5 S235/275/355/JR/J0/J2 5.76
欧标角钢 75*75*6 S235/275/355/JR/J0/J2 6.85
欧标角钢 75*75*7 S235/275/355/JR/J0/J2 7.93
欧标角钢 80*80*5 S235/275/355/JR/J0/J2 6.17
欧标角钢 80*80*6 S235/275/355/JR/J0/J2 7.34
欧标角钢 80*80*7 S235/275/355/JR/J0/J2 7.49
欧标角钢 80*80*8 S235/275/355/JR/J0/J2 9.63
欧标角钢 90*90*7 S235/275/355/JR/J0/J2 9.61
欧标角钢 90*90*8 S235/275/355/JR/J0/J2 10.9
欧标角钢 90*90*9 S235/275/355/JR/J0/J2 12.2
欧标角钢 90*90*10 S235/275/355/JR/J0/J2 13.4
欧标角钢 100*100*8 S235/275/355/JR/J0/J2 12.2
欧标角钢 100*100*9 S235/275/355/JR/J0/J2 13.6
欧标角钢 100*100*10 S235/275/355/JR/J0/J2 15
欧标角钢 100*100*11 S235/275/355/JR/J0/J2 16.4
欧标角钢 110*110*9 S235/275/355/JR/J0/J2 15
欧标角钢 110*110*10 S235/275/355/JR/J0/J2 16.6
欧标角钢 110*110*11 S235/275/355/JR/J0/J2 18.2
欧标角钢 110*110*12 S235/275/355/JR/J0/J2 19.7
欧标角钢 120*120*8 S235/275/355/JR/J0/J2 14.7
欧标角钢 120*120*9 S235/275/355/JR/J0/J2 16.5
欧标角钢 120*120*10 S235/275/355/JR/J0/J2 18.2
欧标角钢 120*120*11 S235/275/355/JR/J0/J2 19.9
欧标角钢 120*120*12 S235/275/355/JR/J0/J2 21.6
欧标角钢 130*130*10 S235/275/355/JR/J0/J2 19.8
欧标角钢 140*140*10 S235/275/355/JR/J0/J2 21.4
欧标角钢 150*150*10 S235/275/355/JR/J0/J2 23
欧标角钢 160*160*14 S235/275/355/JR/J0/J2 33.9
欧标角钢 180*180*13 S235/275/355/JR/J0/J2 35.7
欧标角钢 200*200*13S235/275/355/JR/J0/J2 39.8
欧标角钢 250*250*17 S235/275/355/JR/J0/J2 64.4 
欧标角钢低合金钢性能度钢结构件的屈服点决定了结构所能承受的不发生变形的应力。典型碳素结构钢的小屈服点为235MPa。而典型低合金度钢的小屈服点为345MPa。因此，根据其屈服点的比例关系，低合金度钢的使用允许应力比碳素结构钢高1.4倍。
上饶欧标角钢65*65*4取样位置